for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com 11 11 - 256 linear & power amplifiers - smt hmc486lp5 / 486lp5e surface mount phemt 2 watt power amplifier, 7 - 9 ghz v02.0110 general description features functional diagram the hmc486lp5(e) is a high dynamic range gaas phemt mmic 2 watt power amplifi er housed in a leadless 5x5 mm surface mount packages. operating from 7 to 9 ghz, the amplifi er provides 22 db of gain, +33 dbm of saturated power and 20% pae from a +7v supply voltage. output ip3 is +40 dbm typical. the rf i/os are dc blocked and matched to 50 ohms for ease of use. the hmc486lp5(e) eliminate the need for wire bonding, allowing use of surface mount manufacturing techniques. saturated power: +33 dbm @ 20% pae output ip3: +40 dbm gain: 22 db supply: +7v @ 1300 ma 50 ohm matched input/output 32 lead 5x5mm smt package: 25mm2 electrical specifi cations, t a = +25 c, vdd1, 2, 3, 4, 5 = +7v, idd = 1300 ma* typical applications the hmc486lp5(e) is ideal for: ? point-to-point radios ? point-to-multi-point radios ? test equipment and sensors ? military end-use parameter min. typ. max. min. typ. max. units frequency range 7 - 8 8 - 9 ghz gain 18 21 19 22 db gain variation over temperature 0.05 0.07 0.05 0.07 db/ c input return loss 12 17 db output return loss 8 5 db output power for 1 db compression (p1db) 29 32 28 31 dbm saturated output power (psat) 33 32 dbm output third order intercept (ip3) 41 38 dbm noise figure 7.0 7. 5 d b supply current (idd)(vdd = +7v, vgg = -0.3v typ.) 1300 1300 ma * adjust vgg between -2 to 0v to achieve idd = 1300 ma typical.
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com linear & power amplifiers - smt 11 11 - 257 input return loss vs. temperature output return loss vs. temperature broadband gain and return loss gain vs. temperature p1db vs. temperature psat vs. temperature -25 -15 -5 5 15 25 4567891011 s21 s11 s22 response (db) frequency (ghz) 0 5 10 15 20 25 30 6 6.5 7 7.5 8 8.5 9 9.5 10 +25 c +85 c -40 c gain (db) frequency (ghz) -25 -20 -15 -10 -5 0 6 6.5 7 7.5 8 8.5 9 9.5 10 +25 c +85 c -40 c return loss (db) frequency (ghz) -10 -8 -6 -4 -2 0 6 6.5 7 7.5 8 8.5 9 9.5 10 +25 c +85 c -40 c return loss (db) frequency ( ghz ) 24 26 28 30 32 34 6 6.5 7 7.5 8 8.5 9 9.5 10 +25 c +85 c -40 c p1db (dbm) frequency (ghz) 24 26 28 30 32 34 6 6.5 7 7.5 8 8.5 9 9.5 10 +25 c +85 c -40 c psat (dbm) frequency (ghz) hmc486lp5 / 486lp5e surface mount phemt 2 watt power amplifier, 7 - 9 ghz v02.0110
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com 11 11 - 258 linear & power amplifiers - smt noise figure vs. temperature output ip3 vs. temperature power compression @ 8 ghz gain, power & oip3 vs. supply voltage @ 8 ghz reverse isolation vs. temperature 24 28 32 36 40 44 6 6.5 7 7.5 8 8.5 9 9.5 10 +25 c +85 c -40 c ip3 (dbm) frequency (ghz) 20 22 24 26 28 30 32 34 36 38 40 42 6.5 7 7.5 gain p1db psat ip3 gain (db), p1db (dbm), psat (dbm), ip3 (dbm ) vdd supply voltage (vdc) 20 22 24 26 28 30 32 34 36 38 40 42 700 800 900 1000 1100 1200 1300 gain p1db psat ip3 gain (db), p1db (dbm), psat (dbm), ip3 (dbm ) idd supply current (ma) 0 2 4 6 8 10 12 14 6 6.5 7 7.5 8 8.5 9 9.5 10 +25 c +85 c -40 c noise figure (db) frequency (ghz) -70 -60 -50 -40 -30 -20 -10 0 6 6.5 7 7.5 8 8.5 9 9.5 10 +25 c +85 c -40 c isolation (db) frequency (ghz) 0 6 12 18 24 30 36 -10 -6 -2 2 6 10 14 18 pout gain pae pout (dbm), gain (db), pae (%) input power (dbm) gain, power & oip3 vs. supply current @ 8 ghz hmc486lp5 / 486lp5e surface mount phemt 2 watt power amplifier, 7 - 9 ghz v01.0705
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com linear & power amplifiers - smt 11 11 - 259 vdd (v) idd (ma) +6.5 1330 +7.0 1300 +7.5 1285 typical supply current vs. vdd note: amplifi er will operate over full voltage ranges shown above. vgg adjusted to achieve idd= 1300 ma at +7v. 7 7.5 8 8.5 9 9.5 10 10.5 -10 -6 -2 2 6 10 14 18 power dissipation (w) input power (dbm) 8 ghz max pdiss @ +85c power dissipation* absolute maximum ratings drain bias voltage (vdd1, 2, 3, 4, 5) +8v gate bias voltage (vgg) -2 to 0v rf input power (rfin)(vdd = +7v) +20 dbm channel temperature 150 c continuous pdiss (t = 85 c) (derate 154 mw/c above 85 c) 10 w thermal resistance (channel to ground paddle) 6.5 c/w storage temperature -65 to +150 c operating temperature -40 to +85 c outline drawing * please refer to thermal management for surface mount components application note at www.hittite.com/ part number package body material lead finish msl rating package marking [3] hmc486lp5 low stress injection molded plastic sn/pb solder msl1 [1] h486 xxxx hmc486lp5e rohs-compliant low stress injection molded plastic 100% matte sn msl1 [2] h486 xxxx [1] max peak refl ow temperature of 235 c [2] max peak refl ow temperature of 260 c [3] 4-digit lot number xxxx notes: 1. leadframe material: copper alloy 2. dimensions are in inches [millimeters] 3. lead spacing tolerance is non-cumulative. 4. pad burr length shall be 0.15mm maximum. pad burr height shall be 0.05mm maximum. 5. package warp shall not exceed 0.05mm. 6. all ground leads and ground paddle must be soldered to pcb rf ground. 7. refer to hittite application note for suggested land pattern. package information hmc486lp5 / 486lp5e surface mount phemt 2 watt power amplifier, 7 - 9 ghz v01.0705 electrostatic sensitive device observe handling precautions
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com 11 11 - 260 linear & power amplifiers - smt pin number function description interface schematic 1-3, 5-8, 10-12, 14, 15, 17-20, 22-24, 26, 27, 29-31 n/c no connection required. these pins may be connected to rf/dc ground without affecting performance. 4rfin this pin is ac coupled and matched to 50 ohms. 9vgg gate control for amplifi er. adjust to achieve idd of 1300 ma. please follow mmic amplifi er biasing procedure application note. external bypass capacitors of 100 pf and 2.2 f are required. 21 rfout this pin is ac coupled and matched to 50 ohms. 32, 28, 25, 13, 16 vdd1, vdd2, vdd3, vdd4, vdd5 power supply voltage for the amplifi er. external bypass capacitors of 100 pf and 2.2 f are required. package bottom gnd ground: backside of package has exposed metal ground slug that must be connected to ground through a short path. vias under the device are required pin descriptions application circuit component value c1 100 pf c2 2.2 f hmc486lp5 / 486lp5e surface mount phemt 2 watt power amplifier, 7 - 9 ghz v01.0705
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com linear & power amplifiers - smt 11 11 - 261 evaluation pcb item description j1, j2 sri pc mount sma connector j3, j4 2mm dc header c1 - c6 100 pf capacitor, 0402 pkg. c7 - c12 2.2f capacitor, tantalum u1 hmc486lp5(e) amplifi er pcb [2] 108188 evaluation pcb [1] reference this number when ordering complete evaluation pcb [2] circuit board material: rogers 4350. list of materials for evaluation pcb 108190 [1] the circuit board used in this application should use rf circuit design techniques. signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. a sufficient number of via holes should be used to connect the top and bottom ground planes. copper fi lled vias under the device are recommended. the evaluation board should be mounted to an appropri- ate heat sink. the evaluation circuit board shown is available from hittite upon request. hmc486lp5 / 486lp5e surface mount phemt 2 watt power amplifier, 7 - 9 ghz v01.0705
|
